출장 마사지가 여행 관련 부상을 예방하는 방법
관련 부상을 예방하는 방법 출장에 마사지 요법을 포함시키는 것은 스트레스를 해소하고 휴식을 취하는 좋은 방법이 될 수 있습니다. 많은 여행자들이 장거리 비행, 스트레스가 많은 회의, 바쁜 일정으로 인해 출장 중에 피로와 긴장을 느낍니다. 다행스럽게도 비즈니스 여행객이 휴식을 취하고 생산성...
Corrosion on stained glass is commonly known as white mold. It shows up at the lead or solder lines, leaving the piece of stained glass stained and unattractive. Corrosion or white mold is often the result of flux residue that has not been completely removed.
One method used to remove corrosion is to rub the art glass piece with a cleaner. This will remove corrosion, but it can also cause scratches on the glass.
The best way I have found to remove corrosion is to use baking soda. The baking soda is not as abrasive as the cleaner and will not scratch the glass.
You will need a small scrubbing brush or very fine steel wool. First moisten the scrub brush or steel wool with water. Then generously sprinkle baking soda over the piece. Using the dampened scrubbing brush or steel wool, scrub the glass piece vertically, horizontally, and in circular motions.
Once all corrosion has been removed, rinse off the baking soda thoroughly and dry the art glass piece. If the piece had a patina finish, you may need to patina the piece again. This will depend on how much corrosion has built up on the part.
After the piece is completely dry, use a finishing compound to protect and polish the art glass piece.
This process works very well, although it does take time, work and refinishing. If you have a corroded piece of stained glass, you really don’t have a choice. For future reference, you can prevent corrosion from occurring by properly disposing of the flux when building your next part.
The common cause of corrosion is flux. Never leave flux in a part for more than a few hours. There are a variety of commercial flux removers that you can use. Be sure to follow the manufacturer’s instructions.
I found that CJ is a good commercial flux remover. Following the manufacturers instructions, I spray CJ liberally on one side of the glass piece. Using a soft scrubbing brush, I scrub the glass in circular motions, then rinse the piece with water. Then, following the same procedure, do the other side.
Using baking soda and dish soap is an alternative to commercial flux removers. First, sprinkle the piece with baking soda, then apply a small amount of dish soap to the piece. With a soft, damp scrub brush, use a circular motion to scrub the piece. Rinse with water and then do the other side.
After cleaning and rinsing the part with water, dry it with a clean, soft cloth and allow it to air dry. Once completely dry, the patina can be applied. The last step is to apply the finishing compound on both sides.
Don’t rush cleaning and finishing. A good cleaning and finishing will save you time, work and expenses later.
관련 부상을 예방하는 방법 출장에 마사지 요법을 포함시키는 것은 스트레스를 해소하고 휴식을 취하는 좋은 방법이 될 수 있습니다. 많은 여행자들이 장거리 비행, 스트레스가 많은 회의, 바쁜 일정으로 인해 출장 중에 피로와 긴장을 느낍니다. 다행스럽게도 비즈니스 여행객이 휴식을 취하고 생산성...
postnatal Pilates classes It is generally advised that you wait until at least 6 weeks after the birth of your baby (vaginal) and 8 weeks after a caesarean before starting exercise again, including class-based Pilates. However, some women who were active before pr...
Recovery Process Like After Jaw Slimming A slender, slim jawline can enhance facial beauty, giving it a sculpted appearance. Unfortunately, age and other factors can cause our jawlines to lose definition or become too bulky. Fortunately, a variety of minimally inv...
Sets Masetter Botox Training While a medical aesthetics certification may seem like a small add-on to your current practice, it can actually have a significant impact on your bottom line. This is because Botox and dermal fillers are incredibly popular procedures a...